Increase the coverage of your current wireless network and deliver dual-band WiFi up to 1.9Gbps. Simple Netgear EX6400 Setup; no need to change WiFi names or passphrases. There are two ways to setup your Netgear range WiFi extender: WPS allows you to connect to a secure WiFi network without having to enter the network name or password.

Obtain the NETGEAR installation assistant's assistance: From a computer or mobile device, you must open a web browser in order to use the NETGEAR installation assistant.

Netgear EX6400 Extender Manual Setup

Follow these steps for Netgear EX6400 setup through manual method:

Your Netgear Nighthawk AC1900 EX6400 extender must be turned on.
Put your WiFi extender close to the router.
Connect your extender to a power outlet.
Connect the extender to your router.
From a computer or mobile device, open a web browser and type mywifiext net.

Displayed is the NETGEAR installation assistant.
Use the directions on-screen to connect your extender to your current WiFi network.
Your extender should be relocated.
Try again after moving the extender closer to your router until the Link Status Light turns white if you have poor or no connectivity.

Once you've chosen the ideal place for your extender, connect your client devices to the enlarged WiFi network.

How to configure Netgear EX6400 via WPS?

Using WPS, you can configure your Netgear EX6400 (also known as a Nighthawk AC1900) as follows:

You need to have your Netgear EX6400 WiFi range extender turned on.
Put your WiFi extender close to the router.
Connect your extender to a power outlet.
Watch for the Netgear EX6400's Power LED to turn green.
The extender's WPS button should be pressed.

Your extender and router are connected properly if the EX6400 Link Status LED is white. Blue will appear on the Netgear EX6400 Link Status LED if the connection is strong. Move the extender closer to the router and retry if the Link Status LED flashes amber or red.

Common Problems during Netgear EX6400 Setup

Password for mywifiext not correct
Mywifiext.local cannot be contacted
The network is not connected to the WiFi extender.
The Netgear Genie app won't launch.
192.168.1.250 IP address has problems

misplaced configuration CD
WiFi connection problems
Even after setting up the Netgear AC1900 extender, the Netgear genie smart setup page keeps coming up.
forgotten the default Netgear extender password

The LED lights on the extender are unstable.
Mywifiext com won't launch
No access to the Netgear EX6400 extender
Internet connectivity is lost on the EX6400.

updating Netgear firmware is not possibleAfter a Netgear EX6400 extender update, it is impossible to access mywifiext net.
errors in MAC address filtering
failed update, Netgear EX6400 not working
Internet connection issues with WiFi extenders

No network name for Netgear range extenders

Steps for Troubleshooting Netgear EX6400 configuration Problems

Follow the troubleshooting instructions listed below to resolve Netgear EX6400 setup issues:
Check to see if the Netgear AC1900 extender is getting the right amount of power from the wall outlet.
Verify that the wall plug is not damaged or short-circuited before plugging in the extender.
Verify each and every wired connection. Use only undamaged cables.
Try setting up your Netgear AC1900 extender once more after performing a power cycle.

Install the most recent Netgear firmware on your extender.

Any of the above-mentioned troubleshooting tips failed to address your issues? Not to worry. Simply contact our professionals to resolve your Netgear EX6400 setup issues.

How to Update Firmware on Netgear EX6400 extender?

Has the behaviour of your WiFi extender suddenly changed? Even after a successful Netgear EX6400 setup, is it still not providing the required speed? If so, immediately update the Netgear extender's firmware. The firmware for the Netgear Extender is a set of instructions built into the hardware.

Here's how to update the firmware on a Netgear EX6400:

Start by turning on your Nighthawk AC1900 extender.
Connect the extender to your router.
Once finished, open your preferred web browser.
In the address bar, type mywifiext net and press the enter key.
You must enter the username and password to access your extender.

Click the Firmware Upgrade option under Settings.
then select the Check button.
If a new firmware version is available, press the yes button to upgrade.
Wait a while for the Netgear EX6400 firmware to properly update.

How to Setup Netgear Ex6400?